Control Systems and MCPs - Natural

Product Descriptions

SE Controls provide a range of EN12101-10 compliant control systems to suit every building application.

Click the product image below for full product details and downloads.

 

OS2 SHEVTEC Controller
      

The OS2 SHEVTEC controller is a flexible, fully compliant EN12101-10 control panel that can operate either as a stand-alone, networked, or multi-zoned system. It can also integrate into an OSLoop system to control individual smoke vents with a high-power draw.

Smoke shaft systems are easily programmed aligned to the cause and effect strategy via OSLink insert cards with dip switch selection. Environmental control is also offered to regulate the temperature within the common corridors.

The system is MANAGED PROTOCOL, accessible to any SE Controls authorised Partner or Licenced Installed within the national approved network to ensure the life safety system is correctly serviced and operational.  

 

OSLoop Control System Overview
      

OSloop is a fully compliant EN12101-10 control system that distributes power and data via a loop such that the system still operates if the cable is cut. The local MCP becomes the zonal controller on each floor thus offering savings in fire-rated field wiring costs. The system is designed for both natural and mechanical high-rise residential smoke ventilation systems and can provide system status indication for taller buildings via the SHEVTEC Repeater Panel. 

The system is MANAGED PROTOCOL, accessible to any SE Controls authorised Partner or Licenced Installed within the national approved network to ensure the life safety system is correctly serviced and operational.   
 


Standard Manual Control Point (MCP)

  

The MCP integrates with OSLoop and OS2 Shevtec Controller systems for smoke shaft, corridor AOV and escape/fire-fighting stair and lobby applications.

It provides both open and close/reset activation of AOVs in addition to system monitoring and indication to meet the requirements of prEN12101-9. The MCP is available in both surface mounted and recessed applications.
 

Tamper Proof Manual Control Point (MCP)

The Tamperproof MCP integrates with OSLoop and OS2 Shevtec Controller systems for smoke shaft, corridor AOV and escape/fire-fighting stair and lobby applications.

For installations that may be subject to increased nuisance operation or damage it only provides close/reset activation of smoke ventilators as there is no requirement to manually open a smoke vent in a communal escape corridor. A manual Fireman’s override is however optional via a secure key.

The MCP provides monitoring and indication to meet the requirements of prEN12101-9.

 


Smoke Detector

The smoke detector head and base is a certified, optical detector for use as a smoke detection system within common escape areas within a high-rise residential applications. It is used in conjunction with the OSLoop and SHEVTEC OS2 controls systems to provide a stand-alone, compliant smoke detection and ventilation system and gives a failsafe signal to the controls system if the head is removed or activated.

 

SHEVTEC Repeater Panel
 

The Repeater Panel has been designed to provide system status information for each vent within a smoke ventilation system. The repeater panel would typically be located near the fire service access entrance of the building to provide system indication. Whilst this product is not required under Approved Document B, SE Controls can include this product within the specification to provide system status information in the event of a fire or for system maintenance.

PIR Sensor

PIR sensors are utilised if a smoke ventilator automatically or remotely closes and there is an entrapment risk. This risk is often negated via the use of a local MCP for system reset or physical barriers and cover grilles.


Rain Sensor

The rain sensor is utilised in conjunction with the temperature sensor to close the smoke ventilation AOV when utilised for environmental ventilation as part of an SE Controls ‘Evello’ smoke ventilation system.



Temperature Sensor

The temperature sensor is installed within the common corridor to activate the smoke ventilation system and cool the space as overheating in common corridors is commonplace in this application. This system is called SE Controls ‘Evello’.
 


Human Machine Interface (HMI)

The HMI is a front-end interface that is part of an OSLoop and SHEVTEC OS2 smoke ventilation controls system. It provides the user with real-time status of the system including activations and fault locations. 

Got a question?

If you have a question about any SE Controls products or services, we may already have the answer for you in our FAQs

See our FAQs


Alternatively, contact us on:

E: info@secontrols.com

T: +44 (0)1543 443 060